F910J476KAAAJ6 [KYOCERA AVX]
Automotive Low ESR Tantalum Capacitor;型号: | F910J476KAAAJ6 |
厂家: | KYOCERA AVX |
描述: | Automotive Low ESR Tantalum Capacitor |
文件: | 总3页 (文件大小:597K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
F91-AJ6 Series – Automotive Product Range
F91-AJ6 Series
Low ESR, Resin-Molded Chip - Automotive Product Range
FEATURES
•
•
•
Compliant to the RoHS3 directive 2015/863/EU
Compliant to AEC-Q200
100% Surge Current Tested
LEAD-FREE COMPATIBLE
COMPONENT
APPLICATIONS
•
•
Cabin Electronics
Infotainment
CASE DIMENSIONS: millimeters (inches)
EIA
L ± 0.20
(0.008)
W ± 0.20 (0.008) H ± 0.20 (0.008)
W1 ± 0.20
(0.008)
1.20 (0.047)
2.20 (0.087)
2.40 (0.094)
A ± 0.30 (0.012)
-0.20 (0.008)
0.80 (0.031)
0.80 (0.031)
1.30 (0.051)
Code EIA Code
S Min.
Metric
-0.10 (0.004)
1.60 (0.063)
2.80 (0.110)
4.30 (0.169)
-0.10 (0.004)
1.60 (0.063)
1.90 (0.075)
2.90 (0.114)
A
B
N
1206
1210
2917
3216-18
3528-21
7343-31
3.20 (0.126)
3.50 (0.138)
7.30 (0.287)
1.10 (0.043)
1.40 (0.055)
4.40 (0.173)
W1 dimension applies to the termination width for a dimensional area only
A, B, N CASE
Capacitance Value in pF
476 = 47μF
AVX LOGO
Rated Voltage Code
A = 10V
ID Code
Polarity
Band
(Anode+)
476 A
xxxxx
4V
16V
20V
25V
35V
V
G
J
A
C
D
E
6.3V
10V
*Capacitance code of “P” case products are as shown below.
HOW TO ORDER
1C
AJ6
F91
226
M
B
Type
Rated
Voltage
Capacitance Code
pF code: 1st two
digits represent
Tolerance
K = ±10%
M = ±20%
Case
Size
Packaging
Tolerance
K = ±10%
M = ±20%
See Tape & Reel
Packaging Section
See
significant figures,
3rd digit represents
multiplier (number of
zeros to follow)
table
above
TECHNICAL SPECIFICATIONS
Category Temperature Range
Rated Temperature
Capacitance Tolerance
Dissipation Factor
-55 to +125°C
+85°C
±20%, ±10% at 120Hz
Refer to next page
Refer to next page
ESR 100kHz
After 1 minute’s application of rated voltage, leakage current at 20°C is not
more than 0.01CV or 0.5μA, whichever is greater.
After 1 minute’s application of rated voltage, leakage current at 85°C is not
more than 0.1CV or 5μA, whichever is greater.
After 1 minute’s application of derated voltage, leakage current at 125°C is not
more than 0.125CV or 6.3μA, whichever is greater.
+15% Max. at +125°C
Leakage Current
Capacitance Change By Temperature
+10% Max. at +85°C
-10% Max. at -55°C
The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or
available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.
88
090121
F91-AJ6 Series
Low ESR, Resin-Molded Chip - Automotive Product Range
CAPACITANCE AND RATED VOLTAGE RANGE
(LETTER DENOTES CASE SIZE)
Capacitance
Rated Voltage
10V (1A)
*1: ΔC/C Marked “*”
Item
Damp Heat
Temperature cycles
Resistance soldering heat
Surge
μF
10
Code
6.3V (0J)
16V (1C)
106
226
336
476
107
227
A
A
B
B
A
B
B
All Case (%)
22
A
±10
±10
±10
±10
±10
33
47
A,B
B
100
220
N
N
Endurance
Released ratings
RATINGS & PART NUMBER REFERENCE
Rated
DF
ESR
100kHz RMS Current (mA)
*1
ΔC/C
(%)
AVX
Capacitance
Case Size
Voltage
(V)
DCL (μA)
@ 120Hz @ 100kHz
MSL
Part No.
(μF)
(%)
(mΩ)
25ºC
85ºC
125ºC
6.3 Volt
F910J226#AAAJ6
F910J476#AAAJ6
F910J476#BAAJ6
F910J107#BAAJ6
A
A
B
B
22
47
6.3
6.3
6.3
6.3
1.4
3.0
3.0
6.3
8
18
6
1250
1250
500
245
245
412
435
220
220
371
391
98
98
165
174
*
*
*
*
3
3
3
3
47
100
14
450
10 Volt
F911A106#AAAJ6
F911A226#AAAJ6
F911A336#BAAJ6
F911A476#BAAJ6
F911A227#NCAJ6
A
A
B
B
N
10
22
10
10
10
10
10
1.0
2.2
6
12
8
1500
1250
700
224
245
348
412
1225
201
220
314
371
1102
89
98
139
165
490
*
*
*
*
*
3
3
3
3
3
33
3.3
47
220
4.7
22.0
8
500
12
100
16 Volt
F911C106#AAAJ6
F911C226#BAAJ6
F911C336#BAAJ6
F911C107#NCAJ6
A
B
B
N
10
22
16
16
16
16
1.6
3.5
6
8
1500
950
950
100
224
299
201
269
89
*
*
*
*
3
3
3
3
120
120
490
33
5.3
8
299
269
100
16.0
10
1225
1102
#: "M" for ±20% tolerance, "K" for ± 10% tolerance.ꢀMoisture Sensitivity Level (MSL) is defined according to J-STD-020.
QUALIFICATION TABLE
F91-AJ6 series (Temperature range -55ºC to +125ºC)
Condition
At 40°C, 90 to 95% R.H., 500 hours (No voltage applied)
TEST
Damp Heat
Capacitance Change .................. Refer to the table above (*1)
Dissipation Factor ....................... Initial specified value or less
Leakage Current .......................... Initial specified value or less
(Steady State)
Load Humidity
After 1000 hour’s application of rated voltage in series with a 33Ω resistor at 85°C, 85% R.H.,
capacitors meet the characteristics requirements table below.
Capacitance Change .................. Refer to the table above (*1)
Dissipation Factor ....................... Initial specified value or less
Leakage Current .......................... 125% or less than the initial specified value
At -55°C / +125°C, 30 minutes each, 1000 cycles
Capacitance Change .................. Refer to the table above (*1)
Dissipation Factor ....................... Initial specified value or less
Leakage Current .......................... Initial specified value or less
Temperature Cycles
10 seconds reflow at 260°C, 10 seconds immersion at 260°C.
Capacitance Change .................. Refer to the table above (*1)
Dissipation Factor ....................... Initial specified value or less
Leakage Current .......................... Initial specified value or less
Resistance to Soldering Heat
After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles
at 85ºC, capacitors shall meet the characteristic requirements in the table above.
Capacitance Change ....................Refer to the table above (*1)
Surge
Dissipation Factor .........................Initial specified value or less
Leakage Current ...........................Initial specified value or less
After 2000 hours’ application of rated voltage in series with a 3Ω resistor at 85°C, or derated voltage in series with a 3Ω
resistor at 125°C, capacitors shall meet the characteristic requirements in the table above.
Capacitance Change ................ Refer to the table above (*1)
Endurance
Shear Test
Dissipation Factor..................... Initial specified value or less
Leakage Current ....................... Initial specified value or less
After applying the pressure load of 17.7N for 60 seconds horizontally to the center of capacitor side body which
has no electrode and has been soldered beforehand on a substrate, there shall be found neither exfoliation nor its
sign at the terminal electrode.
Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the
opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with a specified
jig at the center of the substrate so that substrate may bend by1mm as illustrated. Then, there shall be found no
remarkable abnormality on the capacitor terminals.
1% per 1000 hours at 85°C, VR with 0.1Ω/V series impedance,
60% confidence level.
Terminal Strength
Failure Rate
The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or
available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.
89
040120
F91-AJ6 Series
Low ESR, Resin-Molded Chip - Automotive Product Range
AVX SOLID ELECTROLYTIC CAPACITOR ROADMAP
SERIES LINE UP : CONVENTIONAL SMD MnO2
TMJ
ultra
low DCL
THH
230°C COTS+
Hermetic
High Rel.
& Special
THJ
THJ
F97-HT3
High Temp
200°C
175°C auto
135°C auto
TRM
professional
multianode
TRJ
F91-AJ6
F97
Industrial &
Automotive
professional
auto
professional
TAJ
TPS
F93-AJ6
F98-AJ6
auto
auto *T/*U
auto *T/*U
auto
TPM
TPS
F91
multianode
Standard
TAJ
F93
F92
Standard
Low Profile
TAJ
TAC
TPC
Low Proꢀle
microchip
microchip
Low ESR
F98-AS1
undertab,
fused
TLN
TLC
F98
High CV
TLJ
undertab
microchip
undertab
The Important Information/Disclaimer is incorporated in the catalog where these specifications came from or
available online at www.avx.com/disclaimer/ by reference and should be reviewed in full before placing any order.
90
030321
相关型号:
©2020 ICPDF网 联系我们和版权申明